ARK Jetson Carrier Setup

Scripts for building and flashing a Jetson Orin Nano or Orin NX on an ARK Jetson Carrier.

Component	Version
JetPack	6.2.2
L4T (BSP)	R36.5.0
Kernel	Linux 5.15
Host OS	Ubuntu 22.04

Building on a non-22.04 host? setup.sh and build.sh auto-containerize themselves in a 22.04 docker image (docker is auto-installed via apt if missing). See docs/build_host.md for why we pin to 22.04.

Products

Target	Carrier Board
PAB	ARK Jetson PAB Carrier
JAJ	ARK Just a Jetson Carrier
PAB_V3	ARK Jetson PAB V3 Carrier

Build & Flash

1. Setup

Download the BSP, root filesystem, and kernel source tarballs (one time):

./setup.sh

2. Build

./build.sh PAB --clean --provision

• Targets are PAB, JAJ, PAB_V3, or all.
• --clean wipes staging/{TARGET}/ and re-stages from scratch.
• --provision preinstalls ARK-OS and tooling into the image. Omit it for a bare image. To bake in your own packages, edit provision.sh.

3. Add WiFi (optional)

Bake a WiFi profile into the image before flashing:

./scripts/add_wifi_network.sh PAB YourNetworkName YourPassword

Or add it later over the USB connection:

ssh jetson@jetson.local
sudo nmcli dev wifi connect YourNetworkName password YourPassword

4. Flash

Connect to the USB port, then power on with the Force Recovery button held.

./flash.sh PAB

By default flash.sh targets NVMe. Other storage layouts:

./flash.sh PAB --sdcard     # SD card (NVIDIA dev kit modules)
./flash.sh PAB --usb        # USB thumb drive

When flashing completes, SSH in over Micro USB or WiFi:

ssh jetson@jetson.local

Tip: Run ssh-copy-id jetson@jetson.local once so you don't type the password on every connection.

Tip: Run ./scripts/add_ssh_config.sh once to add a jetson host to your ~/.ssh/config. Then ssh jetson works, and reflashing won't trip the "REMOTE HOST IDENTIFICATION HAS CHANGED" warning.

Cameras

Every carrier ships with an IMX219 overlay already selected, so cameras work out of the box: the quad overlay on PAB, the dual overlay on JAJ and PAB_V3. To use a different camera, select an overlay with NVIDIA's jetson-io tool. List what's available:

sudo /opt/nvidia/jetson-io/config-by-hardware.py -l

 Header 1 [default]: Jetson 40pin Header
   ...
 Header 2: Jetson 22pin CSI Connector
   Available hardware modules:
   1. Camera IMX219 Quad
   2. Camera IMX477 Quad
   3. Camera IMX708 Quad

Apply one and reboot:

sudo /opt/nvidia/jetson-io/config-by-hardware.py -n 2="Camera IMX477 Quad"
sudo reboot

See docs/cameras.md for supported sensors, overlay names, and how to verify and stream a camera.

More documentation

• docs/cameras.md — supported sensors, overlays, and streaming
• docs/gpio.md — 40-pin / I2S header GPIO and boot-time pad defaults
• docs/i2c.md — I2C bus map and scanning
• docs/servo_expander.md — PWM / servo output via the ARK Servo Expander (PCA9685) over I2C
• docs/10gbe_ethernet.md — Auvidea M20E 10GbE adapter
• docs/share_wifi.md — share the host PC's WiFi with the Jetson over USB
• docs/performance.md — clock speeds and Super Mode
• docs/kernel_development.md — manual kernel builds and device tree changes
• docs/build_host.md — why the build pins to Ubuntu 22.04